View ST2L05-3300_1735565.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/23 december 2004 v o1 = 1.5, 1.8, 2.5, 2.8, 3.0, 3.3v fixed v o2 = 1.5, 1.8, 2.5, 2.8, 3.0, 3.3v fixed or adjustable from 1.25 to v i - v drop guaranteed output1 current: 1a guaranteed output2 current: 1a 2% output tolerance (at 25c) 3% output tolerance over temp. typical dropout 1.1v (i o1 = i o2 = 1a) internal power and thermal limit stable with low esr output capacitor operating temperature range: 0c to 125c very low quiescent current: 7ma max over temp. available in spak and in dfn 5x6mm package description specifically designed for data storage applications, this device integrates two voltage regulators, each one able to supply 1a and it is assembled in spak and in a new 8-pin surface mounting package named dfn 5x6mm at 8 pins. the first regulator block supplies 1.5v, 1.8v, 2.5v, 2.8v, 3.0v, 3.3v depending on the chosen version. the second one may be fixed to the same values or adjustable from 1.25v to v i - v drop that could power several kind of different micro-controllers. both outputs are current limited and over temperature protected. it is worth underlining the very good thermal performance of the packages spak and dfn with only 2c/w of thermal resistance junction to case. applications are hard disk, cd/dvd-rom, cd/ dvd-r/rw, combo (dvd-rom+cd-r/rw). st2l05 very low quiescent current dual voltage regulator figure 1: block diagram of fixed/adj version dfn spak-5l rev. 6
st2l05 2/23 figure 2: block diagram of fixed/fixed version
st2l05 3/23 table 1: order codes (*) available on request. (1) for tube shipment, change "r" with "-" in the relevant ordering code, dfn is available only in tape & reel. v o1 v o2 spak dfn shipment (1) 1.5 v 1.5 v st2l05r1515k5 (*) st2l05r1515ps (*) tape & reel 1.5 v 1.8 v st2l05r1518k5 (*) st2l05r1518ps (*) tape & reel 1.5 v 2.5 v st2l05r1525k5 (*) st2l05r1525ps (*) tape & reel 1.5 v 2.8 v st2l05r1528k5 (*) st2l05r1528ps (*) tape & reel 1.5 v 3.0 v st2l05r1530k5 (*) st2l05r1530ps (*) tape & reel 1.5 v 3.3 v st2l05r1533k5 (*) st2l05r1533ps (*) tape & reel 1.5 v adj st2l05r1500k5 (*) st2l05r1500ps (*) tape & reel 1.8 v 1.5 v st2l05r1815k5 (*) st2l05r1815ps (*) tape & reel 1.8 v 1.8 v st2l05r1818k5 (*) st2l05r1818ps (*) tape & reel 1.8 v 2.5 v st2l05r1825k5 (*) st2l05r1825ps (*) tape & reel 1.8 v 2.8 v st2l05r1828k5 (*) st2l05r1828ps (*) tape & reel 1.8 v 3.0 v st2l05r1830k5 (*) st2l05r1830ps (*) tape & reel 1.8 v 3.3 v st2l05r1833k5 (*) st2l05r1833ps (*) tape & reel 1.8 v adj st2l05r1800k5 (*) st2l05r1800ps (*) tape & reel 2.5 v 1.5 v st2l05r2515k5 (*) st2l05r2515ps (*) tape & reel 2.5 v 1.8 v st2l05r2518k5 (*) st2l05r2518ps (*) tape & reel 2.5 v 2.5 v st2l05r2525k5 (*) st2l05r2525ps (*) tape & reel 2.5 v 2.8 v st2l05r2528k5 (*) st2l05r2528ps (*) tape & reel 2.5 v 3.0 v st2l05r2530k5 (*) st2l05r2530ps (*) tape & reel 2.5 v 3.3 v st2l05r2533k5 (*) st2l05r2533ps (*) tape & reel 2.5 v adj st2l05r2500k5 (*) st2l05r2500ps (*) tape & reel 2.8 v 1.5 v st2l05r2815k5 (*) st2l05r2815ps (*) tape & reel 2.8 v 1.8 v st2l05r2818k5 (*) st2l05r2818ps (*) tape & reel 2.8 v 2.5 v st2l05r2825k5 (*) st2l05r2825ps (*) tape & reel 2.8 v 2.8 v st2l05r2828k5 (*) st2l05r2828ps (*) tape & reel 2.8 v 3.0 v st2l05r2830k5 (*) st2l05r2830ps (*) tape & reel 2.8 v 3.3 v st2l05r2833k5 (*) st2l05r2833ps (*) tape & reel 2.8 v adj st2l05r2800k5 (*) st2l05r2800ps (*) tape & reel 3.0 v 1.5 v st2l05r3015k5 (*) st2l05r3015ps (*) tape & reel 3.0 v 1.8 v st2l05r3018k5 (*) st2l05r3018ps (*) tape & reel 3.0 v 2.5 v st2l05r3025k5 (*) st2l05r3025ps (*) tape & reel 3.0 v 2.8 v st2l05r3028k5 (*) st2l05r3028ps (*) tape & reel 3.0 v 3.0 v st2l05r3030k5 (*) st2l05r3030ps (*) tape & reel 3.0 v 3.3 v st2l05r3033k5 (*) st2l05r3033ps (*) tape & reel 3.0 v adj st2l05r3000k5 (*) st2l05r3000ps (*) tape & reel 3.3 v 1.5 v st2l05r3315k5 (*) st2l05r3315ps (*) tape & reel 3.3 v 1.8 v st2l05r3318k5 (*) st2l05r3318ps (*) tape & reel 3.3 v 2.5 v st2l05r3325k5 (*) st2l05r3325ps tape & reel 3.3 v 2.8 v st2l05r3328k5 (*) st2l05r3328ps (*) tape & reel 3.3 v 3.0 v st2l05r3330k5 (*) st2l05r3330ps (*) tape & reel 3.3 v 3.3 v st2l05r3333k5 (*) st2l05r3333ps (*) tape & reel 3.3 v adj st2l05r3300k5 st2l05r3300ps tape & reel
st2l05 4/23 table 2: absolute maximum ratings (*) storage temperatures > 125c are only acceptable if the dual regulator is soldered to a pcba. absolute maximum ratings are those beyond which damage to the device may occur. functional operation under these condition is n ot im- plied. table 3: recommended operating conditions table 4: thermal data figure 3: pin connection (top view for spak, top thr ough view for dfn8) table 5: pin description symbol parameter value unit v i operating input voltage 10 v p d power dissipation internally limited i osh short circuit output current - 3.3 v and adjustable output internally limited t op operating junction temperature range 0 to 150 c t stg storage temperature range (*) -65 to 150 c t lead lead temperature (soldering) 10 sec. 260 c symbol parameter value unit v i input voltage 4.5 to 7 v ? v i input voltage ripple 0.15 v t rise input voltage rise time (from 10% to 90%) 1 sec t fall input voltage fall time (from 10% to 90%) 1 sec symbol parameter spak dfn unit r thj-case thermal resistance junction-case 22c/w r thj-amb thermal resistance junction-ambient 26 36 c/w spak dfn symbol name and function 13v i bypass with a 4.7f capacitor to gnd 2 4 adj/n.c. resistor divider connection/not connected 3 8 gnd ground 45v o2 adjustable output voltage: bypass with a 4.7f capacitor to gnd 57v o1 fixed output voltage: bypass with a 4.7f capacitor to gnd 1, 2, 6 nc not connected dfn8 spak
st2l05 5/23 figure 4: application circuit of fixed/fixed version figure 5: application circuit of fixed/adj version note: the regulator is designed to be stable with either tantalum or ceramic capacitors on the input and outputs. the expected values of the input and output x7r ceramic capacitors are from 4.7f to 22f with 4.7f typical. the input capacitor must be connected wi thin 0.5 inches of the v i terminal. the output capacitors must also be connected within 0.5 inches of output pins v o1 and v o2 . there is no upper limit to the size of the input capacitor (for more details see the application hints section). note: in the fixed/adj version, the adjustable output voltage v o2 is designed to support output voltages from 1.25v to v i - v drop . the adjustable output voltage v o2 is set by a resistor divider connected between v o2 (pin4) and ground (pin3) with its centre tap connected to v o2 adj (pin2). the voltage divider resistors are: r 1 connected to v o2 and v o2 adj and r 2 connected to v o2 adj and gnd. v o2 is deter- mined by v ref , r 1 , r 2 , and i adj as follows (for more details see the application hints section): v o2 = v ref (1+r 1 /r 2 ) + i adj r 1
st2l05 6/23 table 6: output1 and output2 dual specification (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) table 7: electrical characteristics of fixed output 1.5v (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . symbol parameter test conditions min. typ. max. unit i gnd quiescent current (fixed/adj) v i 7v i out1,2 = 5ma to 1a 5 ma i gnd quiescent current (fixed/fixed) v i 7v i out1,2 = 5ma to 1a 7 ma i st total current limit i o1 + i o2 2a t shdn thermal shutdown 175 c dt shdn thermal shutdown hysteresis 5 c symbol parameter test conditions min. typ. max. unit v o output voltage 1.5v i o = 5ma to 1a, v i = 4.75 to 5.25v t = 25c 1.47 1.5 1.53 v v o output voltage 1.5v i o = 5ma to 1a, v i = 4.75 to 5.25v 1.455 1.5 1.545 v ? v o line regulation v i = 4.75 to 5.25v, i o = 5ma to 1a 15 mv ? v o load regulation v i = 4.75v, i o = 10ma to 1a 12 mv v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i omin min. output current for regulation 0ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o / ? i o transient response change of v o with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o1 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o / ? i o transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 7/23 table 8: electrical characteristics of fixed output 1.8v (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . symbol parameter test conditions min. typ. max. unit v o output voltage 1.8v i o = 5ma to 1a, v i = 4.75 to 5.25v t = 25c 1.764 1.8 1.836 v v o output voltage 1.8v i o = 5ma to 1a, v i = 4.75 to 5.25v 1.746 1.8 1.854 v ? v o line regulation v i = 4.75 to 5.25v, i o = 5ma to 1a 15 mv ? v o load regulation v i = 4.75v, i o = 10ma to 1a 12 mv v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i omin min. output current for regulation 0ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o / ? i o transient response change of v o with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o1 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o / ? i o transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 8/23 table 9: electrical characteristics of fixed output 2.5v (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . symbol parameter test conditions min. typ. max. unit v o output voltage 2.5v i o = 5ma to 1a, v i = 4.75 to 5.25v t = 25c 2.45 2.5 2.55 v v o output voltage 2.5v i o = 5ma to 1a, v i = 4.75 to 5.25v 2.425 2.5 2.575 v ? v o line regulation v i = 4.75 to 5.25v, i o = 5ma to 1a 15 mv ? v o load regulation v i = 4.75v, i o = 10ma to 1a 12 mv v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i omin min. output current for regulation 0ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o / ? i o transient response change of v o with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o1 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o / ? i o transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 9/23 table 10: electrical characteristics of fixed output 2.8v (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . symbol parameter test conditions min. typ. max. unit v o output voltage 2.8v i o = 5ma to 1a, v i = 4.75 to 5.25v t = 25c 2.744 2.8 2.856 v v o output voltage 2.8v i o = 5ma to 1a, v i = 4.75 to 5.25v 2.716 2.8 2.884 v ? v o line regulation v i = 4.75 to 5.25v, i o = 5ma to 1a 15 mv ? v o load regulation v i = 4.75v, i o = 10ma to 1a 12 mv v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i omin min. output current for regulation 0ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o / ? i o transient response change of v o with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o1 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o / ? i o transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 10/23 table 11: electrical characteristics of fixed output 3.0v (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . symbol parameter test conditions min. typ. max. unit v o output voltage 3.0v i o = 5ma to 1a, v i = 4.75 to 5.25v t = 25c 2.94 3.0 3.06 v v o output voltage 3.0v i o = 5ma to 1a, v i = 4.75 to 5.25v 2.91 3.0 3.09 v ? v o line regulation v i = 4.75 to 5.25v, i o = 5ma to 1a 15 mv ? v o load regulation v i = 4.75v, i o = 10ma to 1a 12 mv v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i omin min. output current for regulation 0ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o / ? i o transient response change of v o with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o1 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o / ? i o transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 11/23 table 12: electrical characteristics of fixed output 3.3v (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . symbol parameter test conditions min. typ. max. unit v o output voltage 3.3v i o = 5ma to 1a, v i = 4.75 to 5.25v t = 25c 3.234 3.3 3.366 v v o output voltage 3.3v i o = 5ma to 1a, v i = 4.75 to 5.25v 3.2 3.3 3.4 v ? v o line regulation v i = 4.75 to 5.25v, i o = 5ma to 1a 15 mv ? v o load regulation v i = 4.75v, i o = 10ma to 1a 12 mv v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i omin min. output current for regulation 0ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o / ? i o transient response change of v o with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o1 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o / ? i o transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 12/23 table 13: electrical characteristics of adjustable output (i o = 10ma to 1a, t j = 0 to 125c, v i = 4.5v to 7v, c i = 4.7f, c o1 = c o2 = 4.7 f, otherwise specified) note 1: bandwidth of 10 hz to 10khz. note 2: 120hz input ripple. note 3: c i = 20f, c 1 and c o2 = 10f. c i , c o1 and c o2 are all x7r ceramic capacitors. note 4: guaranteed by design, not tested in production. note 5: % undershoot or overshoot of v o . application hints external capacitors like any low-dropout regulator, the st2l05 requires external capacitors for stability. we suggest soldering both capacitors as close as possible to the relative pins (1, 4 and 5). input capacitor an input capacitor, whose value is, at least, 2.2f is required; the amount of the input capacitance can be increased without limit if a good quality tantalum or aluminium capacitor is used.smd x7r or y5v ceramic multilayer capacitors could not ensure stability in any condition because of their variable characteristics with frequency and temperature; the use of this capacitor is strictly related to the use of the output capacitors. for more details read the ?output c apacitor section?.the i nput capacitor must be located at a distance of not more than 0.5" from the input pin of the device and returned to a clean analog ground. output capacitor the st2l05 is designed specifically to work with ceramic and tantalum capacitors.special care must be taken when a ceramic multilayer capacitor is used.due to their characteristics they can sometimes have symbol parameter test conditions min. typ. max. unit v o reference voltage i o = 5ma to 1a, v i = 4.75 to 5.25v, t = 25c 1.225 1.25 1.275 v v o reference voltage i o = 5ma to 1a, v i = 4.75 to 5.25v 1.212 1.25 1.287 v ? v o2 line regulation 2 v i = 4.75 to 5.25v, i o = 5ma to 1a 0.35 % ? v o2 load regulation 2 v i = 4.75v, i o = 10ma to 1a 0.4 % v d dropout voltage ? v o = -1% i o = 1a 1.3 v i s current limit v i = 5.5v 1 a i adj adjustable current (sinking) 1 a i ? adj adjustable current change i o = 10ma to 1a 200 na i omin min. output current for regulation 2ma e n rms output noise (1)(4) t = 25c 0.003 % svr supply voltage rejection (2)(4) v i = 5v 60 db ? v o2 / ? i o2 transient response change of v o1 with step load change (3)(4) v i = 5v, i o = 1ma to 1a, t r 1s 10 (5) % v i = 5v, i o = 1a to 1ma, t f 1s 10 (5) ? v o2 / ? v i transient response change of v out1 with application of v i (3)(4) 0 to 5v step input, i o = 1ma to 1a, t r 1s 10 (5) % ? v o2 / ? i o2 transient response short circuit removal response (3)(4) v i = 5v, i o = short to i o = 10ma 20 (5) % t r thermal regulation (4) i o = 1a, t pulse = 30ms 0.1 %/w s temperature stability (4) 0.5 % s long term stability (4) (1000hrs) t j = 125c 0.3 %
st2l05 13/23 an esr value lower than the minimum required by the st2l05 and their relatively large capacitance can change a lot depending on the ambient temperature.the test results of the st2l05 stability using multilayer ceramic capacitors show that a minimum value of 2.2f is needed for both regulators. this value can be increased without limit if the input capacitor value is major or equal to 4.7f, and up to 10f if the input capacitor is minor than 4.7f.surface-mountable solid tantalum capacitors offer a good combination of small physical size for the capacitance value and esr in the range needed by the st2l05. the test results show good stability for both outputs with values of at least 1f. the value can be increased without limit for even better performance such as transient response and noise. important: the output capacitor must maintain its esr in the stable region over the full operating temperature to assure stability. more over, capacitor tolerance and variations due to temperature must be considered to assure that the minimum amount of capacitance is provided at all times. for this reason, when a ceramic multilayer capacitor is used, the better choice for temperature coefficient is the x7r type, which holds the capacitance within 15%. the output capacitor should be located not more than 0.5" from the output pins of the device and returned to a clean analog ground. adjustable regulator the st2l05 has a 1.25v reference voltage between the output and the adjust pins (respectively pin 4 and 2). when a resistor r 1 is placed between these two terminals, a constant current flows through r 1 and down to r 2 to set the overall (v o2 to gnd) output voltage. minimum load current is 2ma max in all temperature conditions. figure 6: application circuit v o = v ref (1+r 1 /r 2 )+i adj r 1 i adj is very small (typically 35a) and constant: in the v o calculation it can be ignored.
st2l05 14/23 typical characteristics figure 7: reference voltage vs temperature figure 8: reference line regulation vs temperature figure 9: reference load regulation vs temperature figure 10: reference voltage vs input voltage figure 11: dropout voltage vs temperature (adjustable output) figure 12: dropout voltage vs input voltage (adjustable output)
st2l05 15/23 figure 13: minimum load current vs temperature (adjustable output) figure 14: adjust pin current vs temperature (adjustable output) figure 15: output voltage vs temperature figure 16: line regulation vs temperature figure 17: load regulation vs temperature figure 18: output voltage vs input voltage
st2l05 16/23 figure 19: dropout voltage vs temperature (fixed output) figure 20: dropout voltage vs input voltage figure 21: supply voltage rejection vs temperature figure 22: supply voltage rejection vs frequency figure 23: quiescent current vs temperature (fixed/adj version) figure 24: quiescent current vs temperature (fixed/fixed version)
st2l05 17/23 figure 25: short circuit removal response figure 26: change of v o with step load change figure 27: change of v o with step load change figure 28: change of v o with step load change figure 29: short circuit removal response figure 30: change of v o with step load change v i =5v, i o =short circuit to 10ma, c o =10 f, c i =22 f all ceramic x5r, t j =25c v i =5v, i o =1ma to 1a, c o =10 f, c i =22 f all ceramic x5r, t j =25c v i =5v, i o =1ma to 1a, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t rise =1s v i =5v, i o =1a to 1ma, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t fall =1s v i =5v, i o =short circuit to 10ma, c o =10 f, c i =22 f all ceramic x5r, t j =25c v i =5v, i o =1ma to 1a, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t rise =1s
st2l05 18/23 figure 31: change of v o with step load change figure 32: change of v o with step load change figure 33: start-up transient figure 34: start-up transient v i =5v, i o =1ma to 1a, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t rise =t fall =1s v i =5v, i o =1a to 1ma, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t fall =1s v i =0 to 5v, i o =1ma, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t rise 1s v i =0 to 5v, i o =1a, c o =10 f, c i =22 f all ceramic x5r, t j =25c, t rise 1s
st2l05 19/23 dim. mm. inch min. typ max. min. typ. max. a 1.78 2.03 0.070 0.080 a2 0.03 0.13 0.001 0.005 c 0.25 0.010 c1 0.25 0.010 d 1.02 1.27 0.040 0.050 d1 7.87 8.13 0.310 0.320 f 0.63 0.79 0.025 0.031 g 1.69 0.067 g1 6.8 0.268 h1 5.59 0.220 h2 9.27 9.52 0.365 0.375 h3 8.89 9.14 0.350 0.360 l 10.41 10.67 0.410 0.420 l1 7.49 0.295 l2 8.89 9.14 0.350 0.360 m 0.79 1.04 0.031 0.041 n 0.25 0.010 v3? 6?3? 6? spak-5l mechanical data po13f1/b
st2l05 20/23 dim. mm. inch min. typ max. min. typ. max. a 0.80 0.90 1.00 0.032 0.035 0.039 b 0.35 0.40 0.47 0.014 0.016 0.018 d 5.00 0.197 d2 4.05 4.2 4.30 0.163 0.165 0.167 e 6.00 0.236 e2 3.40 3.55 3.65 0.134 0.140 0.144 e 1.27 0.049 l 0.70 0.80 0.90 0.028 0.031 0.035 dfn8 (5x6) mechanical data
st2l05 21/23 dim. mm. inch min. typ max. min. typ. max. a 180 7.086 c 12.8 13.0 13.2 0.504 0.512 0.519 d 20.2 0.795 n 60 2.362 t 14.4 0.567 ao 9.70 9.80 9.90 0.382 0.386 0.390 bo 10.85 10.95 11.05 0.423 0.427 0.431 ko 2.30 2.40 2.50 0.090 0.094 0.098 po 3.9 4.0 4.1 0.153 0.157 0.161 p 11.9 12.0 12.1 0.468 0.472 0.476 tape & reel spak-xl mechanical data
st2l05 22/23 table 14: revision history date revision description of changes 18-nov-2004 4 remove ppak version. 24-nov-2004 5 new mechanical data release. 06-dec-2004 6 new mechanical data release.
st2l05 23/23 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the co nsequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this publicati on are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics prod ucts are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectro nics. the st logo is a registered trademark of stmicroelectronics all other names are the property of their respective owners ? 2004 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of ST2L05-3300

	To Download ST2L05-3300 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .